Technical Brief

Annular Frictional Pressure Losses During Drilling—Predicting the Effect of Drillstring Rotation

[+] Author and Article Information
Arild Saasen

Po Box 2070 Vika,
Oslo NO-0125,Norway
e-mail: Arild.Saasen@detnor.no

1Corresponding author.

Contributed by the Petroleum Division of ASME for publication in the JOURNAL OF ENERGY RESOURCES TECHNOLOGY. Manuscript received July 23, 2013; final manuscript received December 2, 2013; published online March 4, 2014. Assoc. Editor: Christopher J. Wajnikonis.

J. Energy Resour. Technol 136(3), 034501 (Mar 04, 2014) (5 pages) Paper No: JERT-13-1220; doi: 10.1115/1.4026205 History: Received July 23, 2013; Revised December 02, 2013

Controlling the annular frictional pressure losses is important in order to drill safely with overpressure without fracturing the formation. To predict these pressure losses, however, is not straightforward. First of all, the pressure losses depend on the annulus eccentricity. Moving the drillstring to the wall generates a wider flow channel in part of the annulus which reduces the frictional pressure losses significantly. The drillstring motion itself also affects the pressure loss significantly. The drillstring rotation, even for fairly small rotation rates, creates unstable flow and sometimes turbulence in the annulus even without axial flow. Transversal motion of the drillstring creates vortices that destabilize the flow. Consequently, the annular frictional pressure loss is increased even though the drilling fluid becomes thinner because of added shear rate. Naturally, the rheological properties of the drilling fluid play an important role. These rheological properties include more properties than the viscosity as measured by API procedures. It is impossible to use the same frictional pressure loss model for water based and oil based drilling fluids even if their viscosity profile is equal because of the different ways these fluids build viscosity. Water based drilling fluids are normally constructed as a polymer solution while the oil based are combinations of emulsions and dispersions. Furthermore, within both water based and oil based drilling fluids there are functional differences. These differences may be sufficiently large to require different models for two water based drilling fluids built with different types of polymers. In addition to these phenomena washouts and tool joints will create localised pressure losses. These localised pressure losses will again be coupled with the rheological properties of the drilling fluids. In this paper, all the above mentioned phenomena and their consequences for annular pressure losses will be discussed in detail. North Sea field data is used as an example. It is not straightforward to build general annular pressure loss models. This argument is based on flow stability analysis and the consequences of using drilling fluids with different rheological properties. These different rheological properties include shear dependent viscosity, elongational viscosity and other viscoelastic properties.

Copyright © 2014 by ASME
Your Session has timed out. Please sign back in to continue.


Ahmed, R., Enfis, M., Miftah-El-Kheir, H., Laget, M., and Saasen, A., 2010, “The Effect of Drillstring Rotation on Equivalent Circulation Density: Modeling and Analysis of Field Measurements,” SPE Annual Technical Conference and Exhibition, Florence, Italy, Sep. 19–22, Paper No. SPE 135587.
Sorgun, M., Ozbayoglu, M. E., and Aydin, I., 2010, “Modelling and Experimental Study of Non-Newtonian Fluids in Annulus,” ASME J. Energy Resour. Technol., 132, p. 033102. [CrossRef]
Haciislamoglu, M., and Langlinais, J., 1990, “Non-Newtonian Flow in Eccentric Annuli,” ASME J. Energy Resour. Technol., 112, pp 163–169. [CrossRef]
Heisig, G., and Neubert, M., 2000, “Lateral Drillstring Vibrations in Extended-Reach Wells,” IADC/SPE Drilling Conference, Feb. 23–25, New Orleans, LA, Paper No. SPE 59235.
Rayleigh, L., 1880, “On the Stability, or Instability, of Certain Fluid Motions,” Proc. R. Soc. London., 11, pp. 57–70. [CrossRef]
Drazin, P. G., and Reid, W. H., 1981, Hydrodynamic Stability, Cambridge University Press, Cambridge, UK.
Rayleigh, L., 1916, “On the Dynamics of Revolving Fluids,” Proc. R. Soc. London, A93, pp. 148–154. [CrossRef]
Taylor, G. I., 1923, “Stability of a Viscous Liquid Contained Between Two Rotating Cylinders,” Philos. Trans. R. Soc. London, Ser. A, 223, pp. 289–343. [CrossRef]
Jeng, J., and Zhu, K. Q., 2010, “Numerical Simulation of Taylor Couette Flow of Bingham Fluids,” J. Non-Newtonian Fluid Mech., 165, pp. 1161–1170. [CrossRef]
Nouri, J. M., and Whitelaw, J. H., 1994, “Flow of Newtonian and Non-Newtonian Fluids in a Concentric Annulus with Rotation of the Inner Cylinder,” ASME J. Fluids Eng., 116, pp. 821–827. [CrossRef]
Hansen, S. A., and Sterri, N., 1995, “Drill Pipe Rotation Effects on Frictional Pressure Losses in Slim Annuli,” SPE Annual Technical Conference and Exhibition, Oct. 22–25, Dallas, TX, Paper No. SPE 30488.
Hansen, S. A., Rommetveit, R., Sterri, N., Aas, B., and Merlo, A., 1999, “A New Hydraulic Model for Slim Hole Drilling Applications,” SPE/IADC Middle East Drilling Technology Conference, Nov. 8–10, Abu Dhabi, United Arab Emirates, Paper No. SPE 57579.
Sterri, N., Saasen, A., Aas, B., and Hansen, S. A., 2000, “Frictional Pressure Losses During Drilling: Drill String Rotation Effects on Axial Flow of Shear Thinning Fluids in an Eccentric Annulus,” Oil Gas Eur. Mag., 26(3), pp. 30–33.
Ahmed, R., and Miska, S., 2008, “Experimental Study and Modeling of Yield Power-Law Fluid Flow in Annuli With Drillpipe Rotation,” SPE/IADC Drilling Conference, March 4–6, Orlando, FL, Paper No. SPE 112604.
Yamada, Y., 1962, “Resistance of a Flow Through an Annulus With an Inner Rotating Cylinder,” Bull. JSME, 58, pp. 302–310. [CrossRef]
Walker, R. E., and Al-Rawi, R., 1970, “Helical Flow of Bentonite Slurries,” 45th Annual Fall Meeting of the SPE of AIME, Oct. 4–7, Houston, TX, Paper No. SPE 3108.
Woo, N., Seo, B., and Hwang, Y., 2005, “Flow of Newtonian and Non-Newtonian Fluids in Annuli with Rotating Inner Cylinder,” 6th World Conference on Experimental Heat Transfer, Fluid Mechanics, and Thermodynamics, Apr. 17–21, Matsushima, Miyagi, Japan.
Sorgun, M., 2013, “Simple Correlations and Analysis of Cuttings Transport With Newtonian and Non-Newtonian Fluids in Horizontal and Deviated Wells,” ASME J. Energy Resour. Technol., 135, p. 032903. [CrossRef]
Wan, S., Morrison, D., and Bryden, I. G., 2000, “The Flow of Newtonian and Inelastic Non-Newtonian Fluids in Eccentric Annuli With Inner-Cylinder Rotation,” Theor. Comput. Fluid Dyn., 13, pp. 349–359.
Escudier, M. P., Oliveira, P. J., and Pinho, F. T., 2002, “Fully Developed Laminar Flow of Purely Viscous Non-Newtonian Liquids Through Annuli, Including the Effects of Eccentricity and Inner-Cylinder Rotation,” Int. J. Heat Fluid Flow, 23, pp. 52–73. [CrossRef]
Fang, P., and Manglik, R. M., 2002, “The Influence of Inner Cylinder Rotation on Laminar Axial Flows in Eccentric Annuli of Drilling Bore Wells,” Int. J. Transp. Phenom., 4(4), p. 257274.
Delwiche, R. A., Lejeune, M., Mawet, P., and Vighetto, R., 1992, “Slimhole Drilling Hydraulics,” 1992 Annual Conference and Technical Exhibition of the SP–E, Oct. 4–7, Washington, DC, Paper No. SPE 24596.
Ward, C., and Andreassen, E., 1998, “Pressure-While-Drilling Data Improve Reservoir Drilling Performance,” SPE Drill. Completion, 13, pp. 19–24. [CrossRef]
Isambourg, P., Bertin, D., and Branghetto, M., 1998, “Field Hydraulic Tests Improve HPHT Drilling Safety and Performance,” SPE Annual Conference and Technical Exhibition, Sep. 27–30, New Orleans, LA, Paper No. SPE 49115.
Charlez, P., Easton, M., and Morrice, G., 1998, “Validation of Advanced Hydraulic Modeling Using PWD Data,” Offshore Technology Conference, May 4–7, Houston, TX, Paper No. OTC 8804.
Green, M. D., Thomesen, C. R., Baroid, W. L., and Bern, P. A., 1999, “An Integrated Solution of Extended Drilling Problems in the Niakuk Field, Alaska: Part II- Hydraulics, Cuttings Transport and PWD,” Annual Conference and Technical Exhibition, Oct 3–6, Houston, TX, Paper No. SPE 56564.
Hemphill, T., Bern, P., Rojas, J. C., and Ravi, K., 2007, “Field Validation of Drillpipe Rotation Effects on Equivalent Circulating Density,” SPE Annual Conference and Technical Exhibition, Nov. 11–14, Anaheim, CA, Paper No. SPE 11070.
Hemphill, T., Ravi, K., Bern, P., and Rojas, J. C., 2008, “A Simplified Method for Prediction of ECD Increase with Drillpipe Rotation,” 2008 SPE Annual Technical Conference and Exhibition, Sep. 21–24, Denver, CO, Paper No. SPE 115378.
Marken, C. D., He, X., and Saasen, A., 1992, “The Influence of Drilling Conditions on Annular Pressure Losses,” SPE Annual Technical Conference and Exhibition, Oct. 4–7, Washington, DC, Paper No. SPE 24598.
Andereck, C. D., Liu, S. S., and Swinney, H. L., 1984, “Flow Regimes in a Circular Couette System With Independently Rotating Cylinders,” J. Fluid Mech., 164, pp. 155–183. [CrossRef]
Hutchinson, M., and Rezmer-Cooper, I., 1998, “Using Downhole Annular Pressure Measurements to Anticipate Drilling Problems,” SPE Annual Technical Conference and Exhibition, Sep. 27–30, New Orleans, LA, Paper No. SPE 49114.
Guillot, D., 1990, “Digest of Rheological Equations,” Well Cementing, E. B.Nelson, ed., Elsevier, Amsterdam, The Netherlands, Appendix A.
American Petroleum Institute, 1995, Recommended Practice on the Rheology and Hydrauliccs of Oil-Well Drilling Fluids, API Recommended Practice 13D, 3rd ed., American Petroleum Institute, Washington, DC.
Chandrasekhar, S., 1981, Hydrodynamic and Hydromagnetic Stability, Dover Publications, Inc., New York, pp. 358–379.
Escudier, M. P., and Gouldson, I. W., 1995, “Concentric Annular Flow With Centerbody Rotation of a Newtonian and a Shear-thinning Liquid,” Int. J. Heat Fluid Flow, 16, pp. 156–162. [CrossRef]
Anifowoshe, O., and Osisanya, S. O., 2012, “The Effect of Equivalent Diameter Definitions on Frictional Pressure Loss Estimation in an Annulus With Pipe Rotation,” SPE Deepwater Drilling and Completions Conference, June 20–21, Galveston, TX, Paper No. SPE 151176.
Yigit, A. S., and Christoforou, A. P., 2006, “Stick-Slip and Bit-Bounce Interaction in Oil-Well Drillstrings,” ASME J. Energy Resour. Technol., 128, pp. 268–274. [CrossRef]
Davey, A., Di Prima, R. C., and Stuart, J. T., 1968, “On the Stability of Taylor Vortices,” J. Fluid Mech., 31, pp. 17–52. [CrossRef]
Zhou, L., Saasen, A., Ahmed, R. M., Miska, S. Z., Takach, N. E., and Yu, M., 2010. “Hydraulics of Drilling With Aerated Muds Under Simulated Borehole Conditions,” ASME J. Energy Resour. Technol., 132, p. 011002. [CrossRef]
Erge, O., Ozbayogly, E. M., Miska, S. Z., Yu, M., Takach, N., Saasen, A., and May, R., 2013, “Effect of Drillstring Defelction and Rotary Speed on Annular Frictional Pressure Losses,” ASME 2013 32nd International Conference on Ocean, Offshore and Arctic Engineering, June 9–14, Nantes, France, Paper No. OMAE2013-10448.


Grahic Jump Location
Fig. 1

The Reynolds number as function of axial velocity during drilling a 12 ¼ in. section with 5 ½ in. drill pipe. Maximum velocity represents a pump rate of 4000 l/min.

Grahic Jump Location
Fig. 2

The Reynolds number as function of axial velocity during laboratory tests in a 2 in. pipe with a 1 in. inner string. Maximum velocity represents a pump rate of 200 l/min.

Grahic Jump Location
Fig. 3

The Taylor number as function of axial velocity during drilling a 12 ¼ in. section with 5 ½ in. drill pipe at 60 rpm. Maximum velocity represents a pump rate of 4000 l/min with a 1.4 s.g drilling fluid.

Grahic Jump Location
Fig. 4

The Taylor number as function of axial velocity during laboratory tests in a 2 in. pipe with a 1 in. inner string. Maximum velocity represents a pump rate of 200 l/min with an un-weighted water polymer mixture. Inner string rotation is 60 RPM.

Grahic Jump Location
Fig. 5

Annular frictional pressure loss measured as equivalent circulating density as function of drillstring rotation rate for a North Sea 8 ½ in. drilling operation. The flow rate is approximately 1700 l/min resulting in a flow velocity around 1.2 m/s. (Data from Erge et al. [40]).



Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In