Abstract

Traditionally, printed circuit assemblies have been fabricated through a combination of imaging and plating-based subtractive processes involving the use of photo-exposure followed by baths for plating and etching in order to form the necessary circuitry on rigid and flexible laminates. The emergence of a number of additive technologies presents an opportunity for the development of processes for manufacturing of flexible substrates by utilizing mainstream additive processes. Aerosol-jet printing is capable of printing lines and spaces below 10 μm in width. The aerosol-jet system also supports a wide variety of materials, including nanoparticle inks, screen-printing pastes, conductive polymers, insulators, adhesives, and biological matter. The adoption of additive manufacturing for high-volume commercial fabrication requires an understanding of the print consistency and electrical mechanical properties. Little literature that addresses the effect of varying sintering time and temperature on the shear strength and resistivity of the printed lines exists. In this study, the effect of process parameters on the resultant line consistency and mechanical and electrical properties has been studied. Print process parameters studied include sheath rate, mass flow rate, nozzle size, substrate temperature, and chiller temperature. Properties include resistance and shear load to failure of the printed electrical line as a function of varying sintering time and temperature. The aerosol-jet machine has been used to print interconnects. Printed samples have been exposed to different sintering times and temperatures. The resistance and shear load to failure of the printed lines have been measured. The underlying physics of the resultant trend was then investigated using elemental analysis and scanning electron microscopy. The effect of line consistency drift over prolonged runtimes has been measured for up to 10 h of runtime. The printing process efficiency has been gaged as a function of the process capability index (Cpk) and process capability ratio (Cp). Printed samples were studied offline utilizing optical profilometry in order to analyze the consistency within the line width, height, and resistance, and shear load to study the variance in electrical and mechanical properties over time.

References

1.
Das
,
R.
,
2018
, “IDTechEx,” IDTechEx, Cambridge, UK, accessed Oct. 5, 2020, https://www.idtechex.com/research/articles/printed-electronics-key-trends-00015712.asp
2.
BCC Research
,
2012
, “Printed Electronics: The Global Market,” BCC Research LLC, Wellesley, MA, accessed Oct. 5, 2020, https://www.bccresearch.com/ market-research/information-technology/printed-electronics-market-ift066b.html
3.
Markets and Markets, 2019, “Printed Electronics”, Markets and Markets, Northbrook, IL, accessed Jan. 15, 2019, https://www.marketsandmarkets.com/PressReleases/printed-electronics-market.asp
4.
Lupo
,
D.
,
Clemens
,
W.
,
Breitung
,
S.
,
Hecker
,
K.
, and
Cantatore
,
E.
,
2013
, “
OE-A Roadmap for Organic and Printed Electronics
,”
E. Cantatore, eds., Applications of Organic and Printed Electronics, Integrated Circuits and Systems, Springer, Boston, MA.10.1007/978-1-4614-3160-2_1
5.
Paulsen
,
J. A.
,
Renn, K. Christenson
,
M.
, and
Plourde
,
R.
,
2012
, “
Printing Conformal Electronics on 3D Structures With Aerosol Jet Technology
,”
Future of Instrumentation International Workshop (FIIW) Proceedings
, Gatlinburg, TN, Oct. 8–9, 2012, pp.
1
4
.10.1109/FIIW.2012.6378343
6.
Krzeminski
,
J.
, Jakubowska, M., Kanthamneni, A., Wagner, D., Detert, M., and Schmidt, B.,
2017
, “
Pads and Microscale Vias With Aerosol Jet Printing Technique
,” 21st European Microelectronics and Packaging Conference (
EMPC
) & Exhibition, Warsaw, Poland, Sept. 10–13, pp.
1
4
.10.23919/EMPC.2017.8346869
7.
Cai
,
F.
,
2014
, “
Aerosol Jet Printing for 3-D Multilayer Passive Microwave Circuitry
,”
44th European Microwave Conference
, Rome, Italy, Oct. 6–9, pp.
512
515
.10.1109/EuMC.2014.6986483
8.
Oakley
,
C.
,
Kaur, J. A. Byford
,
A.
, and
Chahal
,
P.
,
2017
, “
Aerosol-Jet Printed Quasi-Optical Terahertz Filters
,”
67th ECTC
, Orlando, FL, May 30–June 2, pp.
248
253
.10.1109/ECTC.2017.233
9.
Stoukatch
,
S.
,
P.
Laurent
,
S.
Dricot
,
F.
Axisa
,
L.
Seronveaux
,
D.
Vandormael
,
E.
Beeckman
,
B.
Heusdens
, and
J.
Destiné
,
2012
, “
Evaluation of Aerosol Jet Printing (AJP) Technology for Electronic Packaging and Interconnect Technique
,”
Fourth Electronic System-Integration Technology Conference
, Amsterdam, The Netherlands, Sept. 17–20, pp.
1
5
.10.1109/ESTC.2012.6542067
10.
Navratil
,
J.
,
Rericha
,
T.
,
Soukup
,
R.
, and
Hamacek
,
A.
,
2018
, “
Aerosol Jet Printed Sensor on Fibre for Smart and IoT Applications
,” 41st International Spring Seminar on Electronics Technology (
ISSE
), Zlatibor, Serbia, May 16–20, pp.
1
4
.10.1109/ISSE.2018.8443609
11.
King
,
B. H.
,
O'Reilly
,
M. J.
, and
Barnes
,
S. M.
,
2009
, “
Characterizing Aerosol Jet®Multi-Nozzle Process Parameters for Non-Contact Front Side Metallization of Silicon Solar Cells
,” 34th IEEE Photovoltaic Specialists Conference (
PVSC
), Philadelphia, PA, June 7–12, pp.
001107
001111
.10.1109/PVSC.2009.5411213
12.
Khorramdel
,
B. A.
,
Torkkeli
,
M.
, and
Mäntysalo
,
2018
, “
Electrical Contacts in SOI MEMS Using Aerosol Jet Printing
,”
IEEE Journal of the Electron Devices Society
, Vol.
6
, pp.
34
40
.10.1109/JEDS.2017.2764498
13.
Secor
,
E.
,
2018
, “
Principles of Aerosol Jet Printing
,”
Flexible Printed Electron.
,
3
(
3
), p.
035002
.10.1088/2058-8585/aace28
14.
Lang
,
R. J.
,
1962
, “
Ultrasonic Atomization of Liquids
,”
J. Acoust. Soc. Am.
,
34
(
1
), p.
6
.10.1121/1.1909020
15.
Peskin
,
R. L.
, and
Raco
,
R. J.
,
1963
, “
Ultrasonic Atomization of Liquids
,”
J. Acoust. Soc. Am.
,
35
(
9
), pp.
1378
1381
.10.1121/1.1918700
16.
Rodes
,
C.
,
Smith
,
T.
,
Crouse
,
R.
, and
Ramachandran
,
G.
,
1990
, “
Measurements of the Size Distribution of Aerosols Produced by Ultrasonic Humidification
,”
Aerosol Sci. Technol
,
13
(
2
), pp.
220
229
.10.1080/02786829008959440
17.
Ha
,
M.
,
Zhang
,
W.
,
Braga
,
D.
,
Renn
,
M. J.
,
Kim
,
C. H.
, and
Frisbie
,
C. D.
,
2013
, “
Aerosol-Jet-Printed, 1 Volt H-Bridge Drive Circuit on Plastic With Integrated Electrochromic Pixel
,”
ACS Appl. Mater. Interfaces
,
5
(
24
), pp.
13198
13206
.10.1021/am404204q
18.
Ravindran
,
P.
, and
Davis
,
E. J.
,
1982
, “
Multicomponent Evaporation of Single Aerosol Droplets
,”
J. Colloid Interface Sci
,
85
(
1
), pp.
278
288
.10.1016/0021-9797(82)90256-9
19.
Widmann
,
J. F.
, and
Davis
,
E. J.
,
1997
, “
Evaporation of Multicomponent Droplets
,”
Aerosol Sci. Technol
,
27
(
2
), pp.
243
254
.10.1080/02786829708965470
20.
Oliver
,
W. C.
, and
Pharr
,
G. M.
,
1992
, “
An Improved Technique for Determining Hardness and Elastic Modulus Using Load and Displacement Sensing Indentation Experiments
,”
J. Mater. Res.
,
7
(
6
), pp.
1564
1583
.10.1557/JMR.1992.1564
You do not currently have access to this content.