A mechanistic approach for modeling the tapping process is presented. A methodology for computing chip load is developed for an arbitrary tap geometry. The mechanics of cutting for tapping is analyzed, considering it as an oblique cutting phenomenon. The effects of tap geometry (tap diameter, thread pitch, number of flutes, flute helix angle, tooth rake angle, and thread type), workpiece geometry (hole diameter and hole depth), process parameters (spindle speed and tap penetration depth), and process faults (tap runout, axis misalignment, and drilled hole geometry) are incorporated in the model. The model is calibrated using drilling experiments and is validated by comparing experimental tapping results for aluminum 319, aluminum 356, and gray cast iron. In most cases, the tapping forces were predicted within 10 percent of the experimental values.

Issue Section:
Technical Papers
Keywords:
machining, manufacturing processes, cutting, machine theory
Topics:
Cutting, Drilling, Geometry, Stress, Torque, Thread
1.
Johnson
,
E.
,
1950
, “
Some Experiments on Tapping
,”
Proc. Inst. Mech. Eng.
,
162
, p.
412
412
2.
Stromberg
,
N. O.
,
1942
, “
Tap Design
,”
Tool Engineer
,
pp.
99
–
104
.
3.
Lehde, J. W., “Practical Aspects of Tapping,” American Society of Tool and Manufacturing Engineers, Paper No. 697, pp. 1–16.
4.
Henderer
,
W. E.
,
1977
, “
On the Mechanics of Tapping by Cutting
,”
ASME J. Ind.
,
99
, pp.
257
–
262
.
5.
Felder
,
E.
,
Gilormini
,
P.
,
Tronchet
,
L.
, and
Leroy
,
F.
,
1982
, “
A Comparative Analysis of Three Machining Processes: Broaching, Tapping and Slotting
,”
Etude DGRST Materiaux
,
80
, pp.
512
–
513
.
6.
Carroll
,
L.
,
1995
, “
Tapping Deep Hole
,”
Cutting Tool Engineer
,
47
, No.
5
, pp.
36
–
43
.
7.
Agapiou
,
J. S.
,
1994
, “
Evaluation of the Effect of High Speed Machining on Tapping
,”
ASME J. Ind.
,
116
, pp.
457
–
462
.
8.
Sabberwal
,
A. J. P.
,
1961
, “
Chip Section and Cutting Force During the Milling Operation
,”
CIRP Ann.
,
pp.
197
–
203
.
9.
Stabler
,
G. V.
,
1964
, “
The Chip Flow Law and its Consequences,” Proceedings of the International MTDR Conference, University of Birmingham, Sept. 1964
,
Advances in Machine Tool Design and Research
,
p.
243
243
.
10.
Amerago
,
E. J.
,
1967
, “
Cutting With Double Edge Tools: Symmetrical Triangular Cuts
,”
Int. J. Mach. Tool Des. Res.
,
7
, p.
23
23
.
11.
Kline
,
W. A.
,
DeVor
,
R. E.
, and
Lindberg
,
J. R.
,
1982
, “
The Prediction of Cutting Forces in End Milling With Application to Cornering Cuts
,”
Int. J. Mach. Tool Des. Res.
,
22
, pp.
7
–
22
.
12.
Fu
,
H. J.
,
DeVor
,
R. E.
, and
Kapoor
,
S. G.
,
1984
, “
A Mechanistic Model for the Prediction of the Force System in Face Milling Operations
,”
ASME J. Ind.
,
106
, pp.
81
–
88
.
13.
Chandrasekharan
,
V.
,
Kapoor
,
S. G.
, and
DeVor
,
R. E.
,
1998
, “
A Mechanistic Model to Predict the Cutting Force System for Arbitrary Drill Point Geometry
,”
ASME J. Manuf. Sci. Eng.
,
120
, pp.
563
–
570
.
14.
Kapoor
,
S. G.
,
DeVor
,
R. E.
,
Zhu
,
R.
,
Gajjela
,
R.
,
Parakkal
,
G.
, and
Smithey
,
D.
,
1998
, “
Development of Mechanistic Models for the Prediction of Machining Performance: Model Building Methodology
,”
Mach. Sci. Technol.
,
2
, pp.
213
–
238
.
15.
Surendaran, V., 1998, “A Study of Hole Quality in Drilling,” Master’s thesis, University of Illinois at Urbana-Champaign.
16.
Chandrasekharan, V., 1996, “A Model to Predict the Three-Dimensional Cutting Force System for Drilling With Arbitrary Point Geometry,” PhD thesis, University of Illinois at Urbana-Champaign.
Copyright © 2002
 by ASME
You do not currently have access to this content.