This paper describes the machining of elastomers using sharp, woodworking tools and the machining of cryogenically cooled elastomers. Due to the lack of information on tool selection for elastomer machining, a set of thirteen tools that cover different sizes and tool geometries and materials was used in this study. Fixture design was found to be critical in machining of elastomers because of its relatively low elastic modulus. The cutting force created during machining can generate significant deformations in the elastomer workpiece. The finite element technique is used to analyze the structural stiffness of the elastomer workpiece under different geometric configurations. The effective stiffness is defined to quantify and compare the stiffness of elastomer workpiece machined by different tool sizes. The cleanliness of the groove machined by end milling is investigated. Use of some down-cut end-milling tools effectively removed the elastomer material at room temperature and generated a clean groove. The tool configuration and part fixturing are identified as the two most important variables that affect the cleanliness of machined grooves. Cooling the elastomer workpiece by solid carbon dioxide (dry ice) to about −78.6°C improved the machined surface finish.

Issue Section:
Technical Papers
Keywords:
elastomers, machining, cutting, cryogenics, machine tools, finite element analysis
Topics:
Elastomers, Machining, Milling, Stiffness, Cutting, Finite element analysis, Design
1.
ASTM D1566-00, 2000, Standard Terminology Relating to Rubber, American Society for Testing of Materials.
2.
Harper, C., Ed., 1975, Handbook of Plastics and Elastomers, McGraw-Hill.
3.
Gere, J. M., and Timoshenko, S. P., 1997, Mechanics of Materials, 4th Ed., PWS Pub.
4.
Incopera, F. P., and DeWitt, D. P., 1996, Fundamentals of Heat and Mass Transfer, 4th Ed., Wiley.
5.
Jin
,
M.
, and
Murakawa
,
M.
,
1998
, “
High-Speed Milling of Rubber (1st Report)-Fundamental Experiments and Considerations for Improvement of Work Accuracy
,”
Journal of the Japan Society for Precision Engineering
,
64
(
6
), pp.
897
–
901
.
6.
White
,
L.
,
1995
, “
Recycling Rubber-Technologies Add Value to Scrap
,”
European Rubber Journal
,
177
(
2
), pp.
24
–
25
.
7.
McLeish
,
A.
, 1995, “An Improved Process for the Cryogenic Grinding of Flexible Polyurethane Form,” British Plastics and Rubber, Nov., pp. 42–43.
8.
Wang
,
Z. Y.
,
Rajurkar
,
K. P.
, and
Murugappan
,
M.
,
1996
, “
Cryogenic PCBN Turning of Ceramic Si3N4,
”
Wear
,
195
, pp.
1
–
6
.
9.
Wang
,
Z. Y.
, and
Rajurkar
,
K. P.
,
1997
, “
Wear of CBN Tool in Turning of Silicon Nitride with Cryogenic Cooling
,”
Int. J. Mach. Tools Manuf.
,
37
(
3
), pp.
319
–
326
.
10.
Evans
,
C.
,
1991
, “
Cryogenic Diamond Turning of Stainless Steel
,”
CIRP Ann.
,
40
(
1
), pp.
571
–
575
.
11.
Bhattacharyya
,
D.
,
Allen
,
M. N.
, and
Mander
,
S. J.
,
1993
, “
Cryogenic Machining of Kevlar Composites
,”
Mater. Manuf. Processes
,
8
(
6
), pp.
631
–
651
.
12.
Hocheng
,
H.
, and
Pan
,
C. T.
,
1999
, “
The Effects of Cryogenic Surroundings on the Thermal-Induced Damage in Laser Grooving of Fiber-Reinforced Plastic
,”
Mach. Sci. Technol.
,
3
, pp.
77
–
90
.
13.
Zhao
,
Z.
, and
Hong
,
S. Y.
,
1992
, “
Cooling Strategies for Cryogenic Machining from a Materials Viewpoint
,”
J. Mater. Eng. Perform.
,
1
(
5
), pp.
669
–
678
.
14.
Ding
,
Y.
, and
Hong
,
S. Y.
,
1998
, “
Improvement of Chip Breaking in Machining Low Carbon Steel by Cryogenically Precooling the Workpiece
,”
ASME J. Manuf. Sci. Eng.
,
120
, pp.
76
–
83
.
15.
Paul
,
S.
, and
Chattopadhyay
,
A. B.
,
1996
, “
Determination and Control of Grinding Zone Temperature under Cryogenic Cooling
,”
Int. J. Mach. Tools Manuf.
,
36
(
4
), pp.
491
–
501
.
16.
Paul
,
S.
, and
Chattopadhyay
,
A. B.
,
1997
, “
Cryogenic Cooling in Grinding—A New Concept
,”
European Journal Mech Eng
,
42
(
3
), pp.
131
–
135
.
17.
Hong
,
S.
,
2001
, “
Economical and Ecological Cryogenic Machining
,”
ASME J. Manuf. Sci. Eng.
,
123
, pp.
331
–
338
.
18.
Dhar
,
N. R.
,
Paul
,
S.
, and
Chattopadhyay
,
A. B.
,
2002
, “
Role of Cryogenic Cooling on Cutting Temperature in Turning Steel
,”
ASME J. Manuf. Sci. Eng.
,
124
, pp.
146
–
154
.
19.
Altintas, Y., 2000, Manufacturing Automation: Metal Cutting Mechanics, Machine Tool Vibrations, and CNC Design, Cambridge University Press.
20.
Martellotti
,
M. E.
,
1941
, “
Analysis of the Milling Process
,”
Trans. ASME
,
63
, pp.
677
–
700
.
21.
Cook, R. D., Malkus, D. S., and Plesha, M. E., 1999, Concepts and Applications of Finite Element Analysis, Wiley.
22.
Shih, A. J., Lewis, M. A., Luo, J., and Strenkowski, J. S., “
Chip Morphology and Forces in End Milling of Elastomers,” ASME J. Manuf. Sci. Eng., (companion manuscript submitted
).
23.
Strenkowski, J. S., Shih, A. J., Lewis, M. A., Rodkwan, S., and Poirier, D. R., 2002, “Machining of Elastomers,” 2002 NSF Design, Service and Manufacturing Grantees and Research Conference, San Juan, Puerto Rico, Jan. 7–10.
24.
Strenkowski, J. S., Shih, A. J., Rodkwan, S., and Lewis, M. A., 2003, “Machining of Elastomers—Experimental and Numerical Investigation,” 2003 NSF Design, Service and Manufacturing Grantees and Research Conference, Birmingham, Alabama, Jan. 6–9.
Copyright © 2004
 by ASME
You do not currently have access to this content.