Ultrasonic welding was investigated as a method of joining 0.076 in. (1.93 mm) thick aluminum 6061 flat sheet material. Joints were produced with ultrasonic additive manufacturing (UAM) equipment in a modified application of the ultrasonic welding process. Through joint design development, successful welds were achieved with a scarf joint configuration. Using a design of experiments (DOE) approach, weld parameters including weld amplitude, scarf angle, and weld speed were optimized for mechanical strength. Lower angles and higher amplitudes were found to provide the highest strengths within the levels tested. Finite-element studies indicate that 5 deg and 10 deg angles produce an increased relative motion of the workpieces as compared to 15 deg, 20 deg, and 25 deg angles, likely leading to increased strength. Successful joints showed no indication of voids under optical microscopy. As-welded joints produce tensile strengths of 221 MPa, while heat treated joints produce tensile strengths of 310 MPa, comparable to heat treated bulk material. High-temperature tensile testing was conducted at 210 °C, with samples exhibiting strengths of 184.1 MPa, similar to bulk material. Room temperature fatigue testing resulted in cyclic failures at approximately 190,000 cycles on average, approaching that of bulk material.
Skip Nav Destination
Article navigation
January 2017
Research-Article
Seam Welding of Aluminum Sheet Using Ultrasonic Additive Manufacturing System
Paul J. Wolcott,
Paul J. Wolcott
Center for Ultrasonic Additive Manufacturing,
The Ohio State University,
Columbus, OH 43210
e-mail: wolcott.27@osu.edu
The Ohio State University,
Columbus, OH 43210
e-mail: wolcott.27@osu.edu
Search for other works by this author on:
Christopher Pawlowski,
Christopher Pawlowski
Center for Ultrasonic Additive Manufacturing,
The Ohio State University,
Columbus, OH 43210
e-mail: pawlowski.24@osu.edu
The Ohio State University,
Columbus, OH 43210
e-mail: pawlowski.24@osu.edu
Search for other works by this author on:
Leon M. Headings,
Leon M. Headings
Center for Ultrasonic Additive Manufacturing,
The Ohio State University,
Columbus, OH 43210
e-mail: headings.4@osu.edu
The Ohio State University,
Columbus, OH 43210
e-mail: headings.4@osu.edu
Search for other works by this author on:
Marcelo J. Dapino
Marcelo J. Dapino
Center for Ultrasonic Additive Manufacturing,
The Ohio State University,
Columbus, OH 43210
e-mail: dapino.1@osu.edu
The Ohio State University,
Columbus, OH 43210
e-mail: dapino.1@osu.edu
Search for other works by this author on:
Paul J. Wolcott
Center for Ultrasonic Additive Manufacturing,
The Ohio State University,
Columbus, OH 43210
e-mail: wolcott.27@osu.edu
The Ohio State University,
Columbus, OH 43210
e-mail: wolcott.27@osu.edu
Christopher Pawlowski
Center for Ultrasonic Additive Manufacturing,
The Ohio State University,
Columbus, OH 43210
e-mail: pawlowski.24@osu.edu
The Ohio State University,
Columbus, OH 43210
e-mail: pawlowski.24@osu.edu
Leon M. Headings
Center for Ultrasonic Additive Manufacturing,
The Ohio State University,
Columbus, OH 43210
e-mail: headings.4@osu.edu
The Ohio State University,
Columbus, OH 43210
e-mail: headings.4@osu.edu
Marcelo J. Dapino
Center for Ultrasonic Additive Manufacturing,
The Ohio State University,
Columbus, OH 43210
e-mail: dapino.1@osu.edu
The Ohio State University,
Columbus, OH 43210
e-mail: dapino.1@osu.edu
1Corresponding author.
Manuscript received April 27, 2015; final manuscript received June 20, 2016; published online August 15, 2016. Assoc. Editor: Wayne Cai.
J. Manuf. Sci. Eng. Jan 2017, 139(1): 011010 (8 pages)
Published Online: August 15, 2016
Article history
Received:
April 27, 2015
Revised:
June 20, 2016
Citation
Wolcott, P. J., Pawlowski, C., Headings, L. M., and Dapino, M. J. (August 15, 2016). "Seam Welding of Aluminum Sheet Using Ultrasonic Additive Manufacturing System." ASME. J. Manuf. Sci. Eng. January 2017; 139(1): 011010. https://doi.org/10.1115/1.4034007
Download citation file:
Get Email Alerts
Cited By
A Review on Metallic Drilling Burrs: Geometry, Formation, and Effect on the Mechanical Strength of Metallic Assemblies
J. Manuf. Sci. Eng (April 2025)
A Generalized Machining Process Damping Model for Orthogonal Cutting
J. Manuf. Sci. Eng
Related Articles
Microstructural Characterization of Ultrasonically Welded Aluminum
J. Eng. Mater. Technol (January,2005)
Performance Prediction for Ultrasonically Welded Dissimilar Materials Joints
J. Manuf. Sci. Eng (January,2017)
Statistical Characterization of Ultrasonic Additive Manufacturing Ti/Al Composites
J. Eng. Mater. Technol (October,2010)
Ultrasonic Welding Simulations for Multiple Layers of Lithium-Ion Battery Tabs
J. Manuf. Sci. Eng (December,2013)
Related Proceedings Papers
Related Chapters
Defining Joint Quality Using Weld Attributes
Ultrasonic Welding of Lithium-Ion Batteries
Concluding Remarks and Future Work
Ultrasonic Welding of Lithium-Ion Batteries
Motion Analysis for Multilayer Sheets
Ultrasonic Welding of Lithium-Ion Batteries