Class 2 and 3 nuclear piping is designed according to the allowable stress design (ASD) method used in the ASME Boiler and Pressure Vessel (B&PV) code, Sec. III, Division 1, NC and ND-3600 according to which safety factors applied to the strength of steel (resistance) provide acceptable safety margins for the piping design. This paper describes the development of design equations according to the load and resistance factor design (LRFD) method for loads that cause primary stress such as sustained weight, internal pressure, and earthquake for different levels of piping operation. The LRFD method differs from the ASD since multiple factors, applied separately to each load and the strength of steel, provide safety margins that correspond to a known and acceptable probability of failure for the piping. Load combinations are provided, statistical properties for the variables under consideration are presented and the partial safety factors are moreover illustrated for different values of the target reliability index.
Skip Nav Destination
e-mail: clioavr@yahoo.com
e-mail: ba@umd.edu
Article navigation
April 2010
Research Papers
Load and Resistance Factor Design (LRFD) of Nuclear Straight Pipes for Loads That Cause Primary Stress
Kleio Avrithi,
Kleio Avrithi
Department of Civil and Environmental Engineering,
e-mail: clioavr@yahoo.com
University of Maryland
, College Park, MD 20742
Search for other works by this author on:
Bilal M. Ayyub, PE
Bilal M. Ayyub, PE
Professor and Director
Department of Civil and Environmental Engineering, Center of Technology and Systems Management,
e-mail: ba@umd.edu
University of Maryland
, College Park, MD 20742
Search for other works by this author on:
Kleio Avrithi
Department of Civil and Environmental Engineering,
University of Maryland
, College Park, MD 20742e-mail: clioavr@yahoo.com
Bilal M. Ayyub, PE
Professor and Director
Department of Civil and Environmental Engineering, Center of Technology and Systems Management,
University of Maryland
, College Park, MD 20742e-mail: ba@umd.edu
J. Pressure Vessel Technol. Apr 2010, 132(2): 021101 (14 pages)
Published Online: March 31, 2010
Article history
Received:
November 15, 2009
Revised:
December 28, 2009
Online:
March 31, 2010
Published:
March 31, 2010
Citation
Avrithi, K., and Ayyub, B. M. (March 31, 2010). "Load and Resistance Factor Design (LRFD) of Nuclear Straight Pipes for Loads That Cause Primary Stress." ASME. J. Pressure Vessel Technol. April 2010; 132(2): 021101. https://doi.org/10.1115/1.4000976
Download citation file:
Get Email Alerts
Cited By
Surface Strain Measurement for Non-Intrusive Internal Pressure Evaluation of a Cannon
J. Pressure Vessel Technol (December 2024)
Dynamic Response and Damage Analysis of a Large Steel Tank Impacted by an Explosive Fragment
J. Pressure Vessel Technol (February 2025)
Related Articles
A Reliability-Based Approach for the Design of Nuclear Piping for Internal Pressure
J. Pressure Vessel Technol (August,2009)
Deterministic and Probabilistic Fracture Mechanics Analysis for Structural Integrity Assessment of Pressurized Water Reactor Pressure Vessel
J. Pressure Vessel Technol (June,2016)
Applicability of the ASME Exemption Curve for Chinese Pressure Vessel Steel Q345R
J. Pressure Vessel Technol (December,2015)
Brittle Fracture Prevention Model for Pressure Based on Master Curve Approach
J. Pressure Vessel Technol (February,2017)
Related Proceedings Papers
Related Chapters
Lessons Learned: NRC Experience
Continuing and Changing Priorities of the ASME Boiler & Pressure Vessel Codes and Standards
Development of Nuclear Boiler and Pressure Vessels in Taiwan
Companion Guide to the ASME Boiler and Pressure Vessel Code, Volume 3, Third Edition
Part 2, Section II—Materials and Specifications
Companion Guide to the ASME Boiler & Pressure Vessel Code, Volume 1, Second Edition