... results were found to be in excellent agreement with each other and correlated closely with published neutron and synchrotron residual stress measurements when differences in gauge volume and shape were accounted for. 21 02 2011 05 05 2011 02 12 2011 02 12 2011 beams...

.... assembling beams (structures) elasticity fasteners finite element analysis flanges gaskets leak detection maintenance engineering mechanical contact occupational safety pipes pressure vessels rings (structures) 25 02 2010 10 07 2010 16 05 2011 16 05 2011 2011...

... or experimental cost. Modified dry beam model that represents the beam structure submerged under water with FSI Comparison of total energy variations of beam members between 3D wet model and modified 1D model with added mass and damper Finally, so as to further understand the FSI effect...

..., this approach is, in general, better suited than the beam theory for flat face flanges, in particular when the flange width is small. The proposed models are compared with the discrete beam theory and validated using numerical finite element analysis on different flange sizes. beams (structures) elasticity...

... was normalized with respect to the time step size, while the displacements and velocity was normalized in terms of the maximum velocity. 25 10 2007 08 07 2008 06 04 2009 beams (structures) finite element analysis flow simulation lattice Boltzmann methods shells (structures...

... 2007 15 02 2008 22 01 2009 beams (structures) earthquake engineering elasticity plates (structures) seismology sloshing tanks (containers) vibrations liquid storage tank floating roof single-deck sloshing fluid-structure interaction potential theory long-period...

... Young's modulus and an effective Poisson's ratio. fixed tubesheet heat exchanger finite element analysis axial stress temperature difference beams (structures) deformation finite element analysis heat exchangers pipes stress analysis 23 03 2007 19 11 2007 24 11...

...-dependent crack tip conditions. 01 09 2006 20 02 2007 23 07 2008 beams (structures) fracture toughness fracture toughness testing pressure vessels The Network for Evaluating Structural Components (NESC) was set up over ten years ago to address the verification...

... ( ρ ) 1450 kg ∕ m 3 Length ( L ) 20 m Height ( h ) 5 m Depth ( w ) 1 m 29 01 2006 03 01 2007 11 07 2008 beams (structures) bending elastodynamics finite volume methods...

... force of the beam element. This calculation is conducted for all fluid grid points, which are associated with the beam element. Step 5 . Repeat Step 4 for every beam element. Step 6 . Perform the transient analysis of the 3D beam structure using the fluid force computed as before with given...

... points. The minimum size of the element around the notch/crack tip was 0.03 × 0.03 mm 2 on the plane surface. 01 12 2005 19 02 2007 beams (structures) brittle fracture fracture toughness testing pipes Weibull distribution welds beam welds...

... with those calculated using the analytical ( 150 lb ∕ in. ) , stress-classification ( 153.5 lb ∕ in. ) , and elastic-plastic analyses ( 153.3 lb ∕ in. ) . Primary stress distribution along the beam 04 03 2006 28 06 2006 beams (structures...

... analysis mechanical strength beams (structures) floating roof continuous beams dome frames rainwater loading finite element simulation model experiment strength and buoyancy problems Vertical cylindrical tanks with a floating roof are frequently used for bulk storage of crude oil...

... . 30 09 2005 23 10 2005 structural engineering beams (structures) finite element analysis plates (structures) bending failure analysis mechanical strength elasticity mechanical stability risk analysis decision making In a survey article presented at the First...

... fatigue testing beams (structures) Two series of fatigue tests on butt-welded steel pipe were published in WRC Bulletin 433 ( 1 ). The objective of the first test was to extend Markl’s data into the low-cycle range of 100 - 1000 cycles . Four-point tests (Fig. 1 ) were conducted...

... deformation of the vessel. 31 08 2005 05 10 2005 beams (structures) design engineering plastic deformation pressure vessels finite element analysis work hardening nozzles design by analysis criterion of plastic collapse gross plastic deformation strain hardening...