Abstract
A prediction model of gearbox power loss based on dimensionless analysis is proposed. First, the dimensional model of gearbox power loss is established based on similarity criterion, dimensional harmony principle, and fluid mechanics π theorem. Then, the experimental study is carried out on a power loss test bench. Based on the measured data and multiple linear regression method, the coefficients of the influencing factors are calculated, including gear design parameters, lubrication oil parameters, and operating conditions. To validate the prediction model, the gear pairs were tested under various operating conditions, and two new gear sets with different helical angles were also included. The comparison results show good consistency between the measured data and predicted values. The proposed model can be employed to effectively predict the power loss of gearbox and improve the gearbox efficiency.
Issue Section:
Friction & Wear
References
1.
Petry-Johnson
, T. T.
, Kahraman
, A.
, Anderson
, N. E.
, and Chase
, D. R.
, 2008
, “An Experimental Investigation of Spur Gear Efficiency
,” ASME J. Mech. Des.
, 130
(6
), p. 062601. 2.
Achtenova
, G.
, and Pakosta
, J.
, 2016
, Estimation of the Gearbox No-Load Losses, SAE Technical Paper 2016-01-1092.3.
Changenet
, C.
, Leprince
, G.
, Ville
, F.
, and Velex
, P.
, 2011
, “A Note on Flow Regimes and Churning Loss Modelling
,” ASME J. Mech. Des.
, 133
(12
), p. 121009
. 4.
Changenet
, C.
, and Velex
, P.
, 2007
, “A Model for the Prediction of Churning Losses in Geared Transmissions—Preliminary Results
,” ASME J. Mech. Des.
, 129
(1
), pp. 128
–133
. 5.
Seetharaman
, S.
, and Kahraman
, A.
, 2010
, “A Windage Power Loss Model for Spur Gear Pairs
,” Tribol. Trans.
, 53
(4
), pp. 473
–484
. 6.
Seetharaman
, S.
, and Kahraman
, A.
, 2009
, “Load-Independent Spin Power Losses of a Spur Gear Pair: Model Formulation
,” ASME J. Tribol.
, 131
(2
), p. 022201
. 7.
Seetharaman
, S.
, Kahraman
, A.
, Moorhead
, M. D.
, and Petry-Johnson
, T. T.
, 2009
, “Oil Churning Power Losses of a Gear Pair: Experiments and Model Validation
,” ASME J. Tribol.
, 131
(2
), p. 022202
. 8.
Concli
, F.
, and Gorla
, C.
, 2012
, “Oil Squeezing Power Losses in Gears: A CFD Analysis
,” WIT Trans. Eng. Sci.
, 74
, pp. 37
–48
. 9.
Concli
, F.
, and Gorla
, C.
, 2017
, “CFD Simulation of Power Losses and Lubricant Flow in Gearboxes
,” American Gear Manufacturers Association Fall Technical Meeting
, Columbus, OH
, Oct. 22–24
, pp. 2
–14
.10.
Concli
, F.
, and Gorla
, C.
, 2014
, “A CFD Analysis of the Oil Squeezing Power Losses of a Gear Pair
,” Int. J. Comput. Methods Exp. Meas.
, 2
(2
), pp. 157
–167
. 11.
Maccioni
, L.
, Concli
, F.
, and Gorla
, C.
, 2019
, “Lubrication of Gearboxes: CFD Analysis of a Cycloidal Gear Set
,” WIT Transactions on Engineering Sciences
, 123
, pp. 101
–112
.12.
Li
, J.
, Qian
, X.
, and Liu C
, B.
, 2022
, “Comparative Study of Different Moving Mesh Strategies for Investigating Oil Flow Inside a Gearbox
,” Int. J. Numer. Methods Heat Fluid Flow
, 32
(11
), pp. 3504
–3525
. 13.
Hou
, X.
, Wu
, W.
, Gui
, P.
, Zou
, T.
, and Zhang
, J.
, 2022
, “Investigation of Churning Torque for Hydraulic Torque Converter Based on CFD
,” Tribol. Int.
, 174
, p. 107722
.14.
Hildebrand
, L.
, Dangl
, F.
, Sedlmair
, M.
, Lohner
, T.
, and Stahl
, K.
, 2022
, “CFD Analysis on the Oil Flow of a Gear Stage With Guide Plate
,” Forschung im Ingenieurwesen/Eng. Res.
, 86
(3
), pp. 395
–408
. 15.
Martin
, K. F.
, 1978
, “A Review of Friction Prediction in Gear Teeth
,” Wear
, 49
(2
), pp. 201
–238
. 16.
Anderson
, N. E.
, and Loewenthal
, S. H.
, 1981
, “Effect of Geometry and Operating Conditions on Spur Gear System Power Loss
,” ASME J. Mech. Des.
, 103
(4
), p. 103
.17.
Xu
, H.
, Kahraman
, A.
, Anderson
, N. E.
, and Maddock
, D. G.
, 2007
, “Prediction of Mechanical Efficiency of Parallel-Axis Gear Pairs
,” ASME J. Mech. Des.
, 129
(1
), pp. 58
–68
. 18.
Li
, S.
, and Kahraman
, A.
, 2010
, “Prediction of Spur Gear Mechanical Power Losses Using a Transient Elastohydrodynamic Lubrication Model
,” Tribol. Trans.
, 53
(4
), pp. 554
–563
. 19.
Concli
, F.
, 2017
, “Low-Loss Gears Precision Planetary Gearboxes: Reduction of the Load Dependent Power Losses and Efficiency Estimation Through a Hybrid Analytical-Numerical Optimization Tool
,” Forschung im Ingenieurwesen/Eng. Res.
, 81
(4
), pp. 395
–407
. 20.
Massocchi
, D.
, Lattuada
, M.
, Chatterton
, S.
, and Pennacchi
, P.
, 2022
, “SRV Method: Lubricating Oil Screening Test for FZG
,” Machines
, 10
(8
). 21.
Rumbarger
, J. H.
, Filetti
, E. G.
, and Gubemick
, D.
, 1973
, “Gas Turbine Engine Main Shaft Roller Bearing-System Analysis
,” ASME J. Tribol.
, 95
(4
), pp. 401
–416
.22.
Harris
, T. A.
, and Mindel
, M. H.
, 1973
, “Rolling Element Bearing Dynamics
,” Wear
, 23
(3
), pp. 311
–337
. 23.
Femandes
, C.
, Martins
, R. C.
, and Seabra
, J. H. O.
, 2013
, “Friction Torque of Cylindrical Roller Thrust Bearing Lubricated With Wind Turbine Gear Oils
,” Tribol. Int.
, 59
, pp. 121
–128
. 24.
Shen
, Y.
, Rinderknecht
, S.
, and Hoppert
, M.
, 2017
, “General Modelling Method of Power Losses in Transmission With Parameter Identification
,” Forsch Ingenieurwes
, 81
(2–3
), pp. 117
–123
. 25.
Pedro
, M. T. M.
, Fernandes
, C. M. C. G.
, Ramiro
, C. M.
, Martins
, R. C.
, and Seabra
, J. H. O.
, 2013
, “Power Losses at Low Speed in a Gearbox Lubricated With Wind Turbine Gear Oils With Special Focus on Churning Losses
,” Tribol. Int.
, 62
, pp. 186
–197
. 26.
Goncalves
, D. E. P.
, Fernandes
, C. M. C. G.
, Martins
, R. C.
, and Seabra
, J. H. O.
, 2013
, “Torque Loss in a Gearbox Lubricated With Wind Turbine Gear Oils
,” Lubr. Sci.
, 25
, pp. 297
–311
. 27.
Wang
, W.
, 2013
, “Efficiency Modeling and Experimental Verification of Minicar Transmission System
,” Appl. Mech. Mater.
, 288
, pp. 30
–36
. 28.
Guo
, D.
, Chen
, F.
, Liu
, J.
, Wang
, Y.
, and Wang
, X.
, 2019
, “Numerical Modeling of Churning Power Loss of Gear System Based on Moving Particle Method
,” Tribol. Trans.
, 63
(10
), pp. 1
–18
.29.
Chase
, D.
, 2005
, Development of an Efficiency Test Methodology for High-Speed Gearboxes
, Ohio State University
, Columbus, OH
.Copyright © 2023 by ASME
You do not currently have access to this content.
